网络编辑平台

编辑出版

《热加工工艺》编辑部

  电话:029-38316271;029-38316273

  邮箱:rjggy@vip.163.com

在线调查

相关下载

友情链接

您所在位置:首页->Label


增塑挤压-烧结制备多孔Fe3Al过滤管
Preparation of Porous Fe3Al Filter Tube by Power Extrusion Molding and Sintering
荆 鹏, 康新婷, 迟煜頔, 李广忠
点击:7578次 下载:0次
作者单位:西北有色金属研究院 金属多孔材料国家重点实验室, 陕西 西安 710016)
中文关键字:粉末增塑挤压; Fe3Al过滤管; 多孔材料
英文关键字:powder extrusion molding; Fe3Al filter tube; porous materials
中文摘要:采用自制Fe3Al粉末与增塑剂的混合物,用增塑挤压-烧结法制备了多孔Fe3Al过滤管,研究了增塑剂和粉末粒度对过滤管组织和性能的影响。结果表明, 合适的挤压料配比为5%~14%,挤压力为3~5 t;随烧结温度的升高,过滤管的烧结收缩率提高, 最大孔径和相对透气系数呈先增大后降低的趋势; 随增塑剂添加量的增多,过滤管的烧结收缩率、最大孔径和相对透气系数增大,而抗拉强度降低。采用粉末粒度为-500目的Fe3Al粉末配制挤压料,其过滤管的烧结收缩率和相对透气系数明显高于采用 +500目Fe3Al粉末配比的挤压料。最佳配比参数为-500目的粉末、增塑剂添加量7%,烧结工艺为1250 ℃×3 h,此时多孔体的最大孔径为5.4 μm,相对透气系数为31.5 m3/(h·kPa·m2)。
英文摘要:Fe3Al filter tube was prepared by power extrusion molding and sintering using the mixture of Fe3Al powder and additives. The effects of additives and pore size on the microstructure and properties of the tube were studied. The results show that the suitable extrusion pressure and the charge ratio of powder mixture are 3~5 t and 0.05%~0.14%,  respectively;  the shrinkage of filter tube increases with sintering temperature increasing, the maximum pore size and air relative permeability increase first and then reduce; the shrinkage, maximum pore size and air relative permeability of filter tube increase with additives increasing, the tensile strength of extension of filter tube reduces. The shrinkage and air relative permeability of Fe3Al filter with the particle size of -500 tube is better than that of +500. The optimum parameter for product is -500 Fe3Al alloy powder with 7% additives, sintering at 1250 ℃ for 3 h, and then the maximum pore size reaches 5.4 μm and air relative permeability reaches 31.5 m3/(h·kPa·m2).
读者评论

      读者ID: 密码:    点击此处进行授权 点击此处进行授权
我要评论:
国内统一连续出版物号:61-1133/TG |国内发行代码:52-94 |国际标准出版物号:1001-3814 |国际发行代码:SM8143
版权所有©2024热加工工艺》编辑部 陕ICP备10008724号
本系统由北京菲斯特诺科技有限公司设计开发